Furnace Repair in Yukon, OK
Furnaces here run from October through April. If yours quits, tell us what it's doing and a licensed contractor who covers Canadian County will get in touch.
Tell us about the job
It takes about a minute.
Seven months of Yukon winters wear a furnace down
Your furnace works from October through April here, and on the nights that drop to 29°F it runs for hours at a stretch. Most homes in Yukon heat with gas, so that means a lot of burner cycles, a lot of ignition attempts, a lot of wear on the igniter before spring comes. When the igniter goes, the burner won't light and the house starts to cool.
Canadian County has seen 15 winter storms and 97 damaging wind events over the last ten years, and a quarter of Oklahoma households lost power for at least 24 hours in 2024. A furnace that loses power and comes back on can still fail to reignite if a part was already close to worn out. That is often when a homeowner finds out the igniter or the flame sensor had been failing for a while.
- 7 months
- October through April, your furnace is on duty
- 29°F
- the average winter night it heats against
- 59%
- of homes here heat with gas, so most furnaces here burn gas
- 15 winter storms
- in ten years, the nights a failure hurts most
NOAA nClimDiv, 1991–2020 normals
A new furnace would cut about $100 a year off heating for a typical Canadian County home.
Estimates for a typical Canadian County home, compared with an older unit built to the previous federal minimum, from EIA household energy data, Oklahoma fuel prices and NOAA climate normals. Your home will differ.
Repair makes sense when one part has failed and the heat exchanger is sound.
Replacement makes sense when the heat exchanger is cracked or the furnace keeps needing parts.
Oklahoma requires HVAC contractors to hold a state license.
The license comes from the Construction Industries Board, and it belongs to the contractor, not to the job. The board tested the contractor before handing it out, and that license is on record with the state. It does not get reissued for each furnace someone works on. It is the person or company that is licensed, not the repair.
For a furnace repair, that license is what stands behind the work. Furnace repair means gas lines and burners, and a bad connection there is the dangerous part of the job. The state's answer is the license itself, held by whoever comes out to Canadian County to work on it. In a county where most homes, 58.8% of them, heat with gas, that is the protection this job runs on.
Source: Oklahoma State Legislature
- Why won't my furnace turn on?
- Most of the time the thermostat isn't sending power to the furnace, or the furnace is getting power but failing to start a heat cycle. Check that the thermostat is set to heat and the temperature is above room temperature, and check the breaker and the furnace's own power switch, which looks like a light switch near the unit. If those are fine, the igniter, the flame sensor, or a safety switch could be stopping it, and those need a contractor to test and replace. Winters here run cold enough, down to 29°F on average, that this isn't something to leave for long.
- Why is my furnace blowing cold air?
- If air is moving but it's not warm, the furnace likely isn't igniting even though the blower is running. Start by checking the air filter, since a clogged one can trigger the furnace to shut off the burners while the fan keeps going. If the filter is clean, the igniter or flame sensor is a common cause, and either one needs a contractor to check. A furnace that blows cold air on and off, rather than just at startup, usually means it's shutting down mid-cycle, which points to the same parts.
- Why won't my furnace pilot light stay lit?
- This almost always comes down to the thermocouple, the small sensor that tells the gas valve the pilot is burning. When it wears out or sits out of position, the valve shuts the gas off as a safety measure, and the pilot goes out. A draft blowing across the pilot can also do it, so check if it's near a vent or a door that gets opened often. If relighting it following the furnace's instructions doesn't hold the flame, the thermocouple needs replacing, which is a job for a licensed contractor since it involves the gas line.